日本熟睡的继拇HD3,妻子8免费完整高清,俘虏之锁动漫1-2季全集在线观看

當前位置：首頁 - 新聞動態 > 行業資訊

行業資訊

行業資訊公司新聞

行業資訊

聯系我們

濟南福華建材廠

聯系人：吳老師　

電話：　

手機：13864111871
0531-81901300
地址：山東省濟南市高新開發區巨野河辦事處山圈村西

批刮膩子粉的七個要點

來源：http://m.gyxxhyy120.com 日期：2022-12-01 發布人：

刮膩子是裝修的必要程序，可以使墻面基層高低不平的地方變得平整光滑，還能有效避免外界的水汽腐蝕墻壁，是基層處理中重要的步驟，今天我們就來說說批刮濟南膩子粉的七個要點。

Puttying is a necessary procedure for decoration, which can make the uneven areas of the wall base level smooth and smooth, and can also effectively prevent external moisture from corroding the wall. It is an important step in the treatment of the base level. Today, we will talk about the seven key points of applying putty powder in Jinan.

1、刮膩子施工前需進行測量

1. Measure before puttying

刮膩子施工前，需要先用尺子來進行測量，看看墻面是否水平，以便于確定刮膩子的方式。刮膩子一般施工兩遍即可，不僅讓墻面更加平整，而且能將底色覆蓋掉。如果墻面不平整的地方，則涂刮多遍膩子來進行找平處理，但每道膩子施工間隔應在兩三小時，確保墻面充分干燥。

Before puttying, measure with a ruler to see if the wall is horizontal, so as to determine the method of puttying. Putty is generally applied twice, which not only makes the wall more flat, but also covers the background color. If the wall surface is uneven, apply putty for several times for leveling, but the construction interval of each putty shall be two or three hours to ensure that the wall surface is fully dry.

2、膩子粉施工需做基層處理

2. Base course treatment is required for putty powder construction

檢查基面及基層清理，包括清除墻面砂灰結塊、浮砂及塵土，以提高膩子粉的施工面基層的平整度和附著力，確保基面無污染，無空鼓，無縫隙，無疏松無掉粉現象。

Check the cleaning of the base surface and base course, including the removal of sand and ash caking, floating sand and dust on the wall, to improve the flatness and adhesion of the base course of the putty powder construction surface, and ensure that the base surface is free of pollution, hollowing, cracks, looseness and powder loss.

3、施工溫度要在5℃以上

3. The construction temperature shall be above 5 ℃

施工環境一直都是非常重要的因素，如果環境溫度過低，容易影響到膩子中有機添加劑的溶解，如果添加劑不能充分溶解，或是溶解速度過慢，將影響膩子批刮后的成膜質量和施工性能。施工環境過熱、過干也不行，膩子施工適宜在5℃-35℃的環境下進行。

The construction environment has always been a very important factor. If the ambient temperature is too low, it is easy to affect the dissolution of organic additives in the putty. If the additives cannot be fully dissolved or the dissolution rate is too slow, it will affect the film quality and construction performance of the putty after batching. The construction environment is neither too hot nor too dry. The putty construction should be carried out at 5 ℃ - 35 ℃.
濟南膩子粉

4、膩子批刮厚度在0.5mm-1mm之間

4. The thickness of putty is 0.5mm-1mm

膩子的批刮不能太薄也不能太厚。太薄的話，膩子層容易失水過快導致膩子出現粉化，終會影響涂裝的效果。而膩子層批刮得越厚，則其干縮強度越大，越容易開裂。因此，單次膩子的批刮厚度好是在0.5mm-1mm之間。

The putty shall not be too thin or too thick. If the putty layer is too thin, it is easy to lose water too quickly, which will lead to putty pulverization, and will eventually affect the coating effect. The thicker the putty layer is scraped, the greater its dry shrinkage strength and the easier it is to crack. Therefore, the batch thickness of single putty is better between 0.5mm-1mm.

5、膩子攪拌好放置幾分鐘，再攪拌使用

5. The putty shall be mixed and placed for several minutes before being used

在攪拌后放置一會兒，是為了給膩子中的成分提供充分溶解的時間以保證膩子的施工性能和后期成膜質量，避免造成添加劑的浪費。膩子在調制成膏狀后，好在半小時內使用，以免膩子變質影響施工效果。

Place it for a while after mixing to provide sufficient time for the ingredients in the putty to dissolve, so as to ensure the construction performance of the putty and the film quality in the later stage, and avoid the waste of additives. After the putty is mixed into a paste, it is better to use it within half an hour to avoid the deterioration of putty affecting the construction effect.

6、底層膩子未干透不得做面層

6. The bottom putty is not completely dry, and no surface course is allowed

內墻膩子粉膩子層不宜過厚，一定要等干透方可批二遍膩子。冬季施工，注意防凍通風干燥，底層膩子未干透不得做面層。

The putty powder putty layer of the interior wall should not be too thick, and the putty can be applied twice only after it is completely dry. During winter construction, pay attention to antifreeze, ventilation and dryness, and do not make surface layer until the bottom putty is completely dry.

7、刮膩子，這些部位要貼布處理

7. Putty, these parts shall be treated with cloth

如果使用普通膩子，或耐水膩子，則輕體墻、隔墻板之間接縫處、家具和墻面接縫處、墻面開槽處等部位好采用貼布處理工藝。如果使用彈性膩子就可以不用貼布處理，直接批刮即可。

If ordinary putty or water-resistant putty is used, the joints between light wall and partition board, the joints between furniture and wall, and the wall grooving should be treated with cloth pasting. If elastic putty is used, it can be directly scraped without sticking cloth.

批刮膩子不僅可以讓墻面更美觀，延長墻壁的壽命，還可以協助房間的防潮，注意以上事項，才能讓發揮膩子的作用，讓房屋得到真正的保護。關注我們帶http://m.gyxxhyy120.com你了解更多！

Applying putty can not only make the wall more beautiful and prolong the life of the wall, but also help the room to prevent moisture. Pay attention to the above items, so that the putty can play its role and the house can be truly protected. Follow us http://m.gyxxhyy120.com You know more!

上一篇：粘結砂漿與抹面砂漿有什么不同？
下一篇：調配石膏粉時的凝固時間掌握

相關推薦：

???

^{<sub id="dc6jw"></sub>}

聯系方式：